Shuttle DS47
Slim PC sin ventilador, con procesador Intel Celeron 847
El Shuttle barebone DS47 se presenta en una carcasa de acero negro y especialmente robusto. Dado que prescinde absolutamente de ventilador y dispone de dos puertos serie y dos conexiones Gigabit Ethernet, se abren para este modelo unos campos de aplicación muy especiales.
Además del procesador Intel Celeron 847 (caché de 2 MB, 2x 1,10 GHz), va integrada ya la LAN inalámbrica (802.11 b/g/n). Este dispositivo, de tan solo 39 mm de grosor, permite integrar hasta 16 GB de memoria DDR3 SO-DIMM y una unidad HDD/SSD de 2,5" con SATA de 6 Gbit/s. La instalación de estos componentes es especialmente sencilla gracias a las tapas que se abren aparte. USB 3.0, HDMI, DVI y un lector de tarjetas redondean el equipamiento del DS47 con refrigeración pasiva. Para la máxima flexibilidad en la colocación y el montaje, ya van incluidos el pie de apoyo y el soporte VESA.
Intel® NM70
Intel Celeron 847
2 x SO-DIMM DDR3-1333 hasta 16Gb
DVI-I + HDMI
2 x RS232
Fuente ext. 65W fanless
Hoja de datos
- Audio
- Audio Realtek® ALC 662 High-Definition Audio (5.1 channel)
Two analog audio connectors (3.5mm) at the back panel:
1) 2 channel line out (head phone)
2) microphone input
Digital multi-channel audio output: via HDMI
- Fanless and silent
- Passive cooling, no fan noise at all
Perfect to be used in noise-sensitive environments
Fanless, dust-free and thus virtually maintenance-free
- Low power consumption
- Power consumption: idle: 10-11W, full load: 22-30W (without/with graphics)
(measured with 2x 2GB SO-DIMM, 500 GB 2.5" hard disk)
- 24/7 nonstop operation
- This device is approved for 24/7 permanent operation.
Requirements:
- Free circulation of air amongst the PC must be guaranteed.
- Ventilation holes must stay clear.
- If a hard disk is installed, this must also be approved for permanent operation by its manufacturer
- Chassis
- Slim-PC (Nettop) with black chassis made of steel
Without cooling fan, passive cooling only
The bays for memory, 2.5" drives and Mini-PCIe cards
can be easily accessed by removing two cover plates.
Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres
Weight: 1.43 kg net and 2.13 kg gross
Two holes for Kensington Lock and numerous
threaded holes (M3) at both sides of the chassis
- Operation Position
- 1) Device must only be used in vertical position with the DVI port facing up
2) Please make sure to use either the supplied feet or the VESA mount
- Operation System
- This barebone system comes without operating system.
It is compatible with Windows 8, Windows 7, Windows XP and Linux
Supports 32 and 64 bit.
- Processor
- Model: Intel Celeron 847
Code name: Sandy Bridge (2nd Gen. Core)
Cores / Threads: 2 / 2
Clock rate: 1.1 GHz
L1/L2/L3 cache: 128 kB / 512 kB / 2048 kB
Memory controller: DDR3-1066/1333 Dual Channel
TDP wattage: 17 W maximum, 13.8W typical
Manufacturing process: 32 nm
Socket: FCBGA1023
Enhanced SpeedStep technology
Maximum Tjunction Temperature: 100°C
Integrated Intel HD graphics engine
Supports 64 Bit, VT-x with EPT, SpeedStep
- Integrated graphics
- Intel HD graphics
Clock rate: 350~800 MHz
Maximum resolution: 2560 x 1600 (analog), 1920 x 1200 (digital, DVI-D / HDMI)
Execution Units (EU): 6
Supports two independent screens
Supports DirectX 10.1, Shader 4.1, OpenGL 3.0
HDMI supports HD video plus multi-channel digital audio via a single cable
- Mainboard / Chipset / BIOS
- Shuttle Mainboard FS47
All capacitors are high quality solid capacitors
Chipset: Intel® NM70 Express
Supports resume after power failure
Supports Wake on LAN (WOL)
Supports Power on by RTC Alarm
Supports boot from USB devices and SD card reader
AMI BIOS in 8 MByte EEPROM with SPI interface
Supports hardware monitoring and watch dog functionality
Supports Unified Extensible Firmware Interface (UEFI) [1]
- Power Adapter
- External 65 W power adapter (fanless)
Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
Output: 19 V DC, max. 3.42 A, max. 65 W
DC Connector: 5.5/2.5mm (outer/inner diameter)
- Memory support
- 2x SO-DIMM slots with 204 pins
Supports DDR3-1066 (PC3-8500) and DDR3-1333 (PC3-10600) SDRAM
DDR3-1600 (PC3-12800) is supported at 1333 MHz clock rate.
Supports Dual Channel mode
Supports max. 8 GB per DIMM, maximum total size of 16 GB
Supports two unbuffered DIMM modules (no ECC)
- Mini PCIe Slots
- Two Mini PCI Express expansion slots: full size and half size
1) the half size slot is occupied with a WLAN module
2) the full size slot supports PCIe 2.0, SATA 3G and USB 2.0
and can either be used for a Mini-PCIe card or
for a Mini SATA (mSATA) flash memory card
Please use the "Mini-PCIE / mSATA Select" function in the BIOS setup.
- Dual Gigabit LAN Controller
- Dual Realtek 8111G Ethernet network controller (Gigabit)
Supports 10 / 100 / 1.000 MBit/s operation
With two RJ45 ports (dual network) supports Teaming
Supports WAKE ON LAN (WOL)
Supports network boot by Preboot eXecution Environment (PXE)
- Wireless Network (WLAN)
- Built-in Mini-PCIe WLAN card (half size) and internal antenna
Supports IEEE 802.11b/g/n, max. 150Mbps up-/downstream
Security: WPA/WPA2(-PSK), WEP 64/128bit, IEEE 802.11x/i
- 2.5 drive bay
- Supports one Serial ATA hard disk
or one SATA SSD drive in 6.35cm/2.5" format
Device height: 9.5 or 12.5 mm (max.)
Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
Supports Unified Extensible Firmware Interface (UEFI)
Note: no Serial ATA cable is required
- Card Reader
- Integrated SD card reader
Supports SD, SDHC and SDXC memory flash cards
Supports boot up from SD card
- Front Panel connectors
- 4x USB 2.0
2x RS232 serial ports (5V/12V, 1x switchable to RS422 / RS485)
SD card reader (supports SD, SDHC, SDXC)
Power button
Power LED (blue)
HDD LED (yellow)
- Back Panel connectors
- HDMI 1.3 connector (supports DVI-D with optional adapter)
DVI-I connector (supports VGA with optional adapter)
2x USB 3.0
2x Gigabit LAN (RJ45)
Microphone input
Audio Line-out (headphone)
DC-input connector for external power adapter
4 pin connector (2.54 mm pitch) for power button, Clear CMOS and 5V DC [4]
Perforation for optional Wireless LAN antennas (2 holes)
- Other onboard connectors
- Connector for CMOS battery (with battery)
Fan connector (4 pins) not occupied
LVDS connector (50 pins)
Jumpers for panel voltage and converter voltage select
- Scope of delivery
- Multi-language user guide
Two metal feet
VESA mount for 75/100mm standard (two metal brackets)
Four thumbscrews M3 x 5 mm (screws together VESA mount and PC)
Four screws M4 x 10 mm (to fix the VESA mount to the external device)
Three screws M3 x 4 mm and a rack (to mount a 2.5" storage into the bay)
Driver DVD (Windows 8 / 7 / XP)
External power adapter with power cord
- Environmental Specifications
- Operating temperature range: 0~40 °C
Relative humidity, non-condensing: 10~90%
- Conformity/Certifications
- EMI: FCC, CE, BSMI, C-Tick
Safety: CB, BSMI, ETL, CCC
This device is classed as a technical information
equipment (ITE) in class B and is intended for use in
living room and office. The CE-mark approves the
conformity by the EU-guidelines:
- EMV-guideline 89/336/EWG electromagnetic tolerance
- LVD-guideline 73/23/EWG use of electric devices
within certain voltage-limits